
Reference: MA006
Brand: MicroTec
Large Dolphin/Gator Clips
The 4mm socket in the back of the Dolphin clip offers an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 30mm opening diameter limit.
This is a brand-new lead and offers dynamic measurement of resistance which is a feature we are using within our guided tests. The TA432 can be used to test diodes, in addition to resistance measurements.
NOTE: This product is fitted with a PicoBNC+ interface, allowing it to be recognised by the software for auto-configuration.
The product requires a PicoScope featuring the PicoBNC+ such as the PicoScope 4225A or PicoScope 4425A, and will not work with older PicoScope models.
Customer service (+45) 97 84 11 99
Fast delivery 1-2 business days
Secure payment via SSL connection
The TA432 has a total lead length of 2m in a Y configuration, with the non-PicoBNC+ ends being 1m in length and terminated in a 4mm non-shrouded connection. The lead contains an active current source and is intended to be used only on unpowered components and wires.
The specification of the TA432 is:
Attribute | Published specification |
Model | PicoBNC+ resistance test lead |
Combined length of lead and probe | 2 m |
Maximum voltage and CAT ratings | +/-30 V ref PC Ground, not CAT rated |
Hardware Resolution | Range 200 Ω with resolution of 0.1 Ω Range 2 kΩ with resolution of 1 Ω Range 20 k Ω with resolution of 10 Ω Range 200 kΩ with resolution of 100 Ω Range 2 MΩ with resolution of 1 kΩ (PicoScope 7 only) |
Hardware Accuracy | Range 200 Ω with accuracy of 2 Ω Range 2 kΩ with accuracy of 20 Ω Range 20 kΩ with accuracy of 200 Ω Range 200 kΩ with accuracy of 5 kΩ Range 2 MΩ with accuracy of 50 kΩ (PicoScope 7 only) |
Diode test | Sub 2 V Voltage range for diode measurement |
Scaling factor and ranges | Auto ranging for resistance starting HIGH Diode test is a single fixed range Default choice is resistance Auto range does not include the diode range |
Calibration / zero offset requirements | On start up |
Reference: MA006
Brand: MicroTec
The 4mm socket in the back of the Dolphin clip offers an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 30mm opening diameter limit.
Reference: MA100
Brand: MicroTec
Test leads with 4mm safety banana plug at both ends, set of 5 colors (Red, black, yellow, green and blue).Can be used with all our probes, tips, clips and gators. Length: 1 meterMax. current: 15A
Reference: TA010
Brand: Pico Technology
The TA010 has been designed to allow fuel injector and primary ignition waveforms to be measured using PicoScope oscilloscope products. The TA010 is a passive 20:1 attenuator. This means that a 20V signal at its input will appear as a 1V signal on the output. As the signal is attenuated, the TA010 allows voltages of up to 300 V to be measured. Please note...
Reference: TA035
Brand: Pico Technology
Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and replace it with a...
Reference: MA012
Brand: MicroTec
The MA012 AMP breakout lead enables you to take voltage readings from the numerous 2-pin sensors and actuators in the engine compartment. Simply connect the breakout lead into the existing cable loom, and then take the output signal from the two 4 mm banana plugs into the automotive oscilloscope using the TA000 test leads. The breakout cable gives access...
Reference: TA037
Brand: Pico Technology
HT extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on COP ignition systems.
Reference: TA162
Brand: Pico Technology
These probes are designed for back-probing under the insulation of multi-plug terminals. The TA161 and TA162 have flexible bends to improve access to difficult areas. Each probe fits onto the 4mm plug of our BNC to 4mm test leads.
Reference: TA018
Brand: MicroTec
60A AC/DC current clamp with BNC connector and 2.5 meter long cable.The TA018 current clamp can measure currents from 10 mA up to 60 A with a switch-selectable high and low range. A simple pushbutton is included for zero adjustment when measuring DC current. The TA018 current clamp meets IEC 61010-1 CAT II 300V and is equipped with LED indication for...
Reference: TA475
Brand: Pico Technology
Our premium PicoBNC+ leads are color-coded so that the color of the lead in the engine bay matches the color of the on-screen waveform in PicoScope Automotive – never again will you waste your time wondering which lead is which. NOTE: This product is fitted with a PicoBNC+ interface, allowing it to be recognised by the software for auto-configuration.The...
Reference: TA004
Brand: Pico Technology
The crocodile (gator) clips are fully insulated with a 4mm socket in the handle, offering an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 11mm jaw opening limit.
Reference: TA167
Brand: Pico Technology
This current clamp is suitable for measuring currents of upto 2000 A DC or 1500 A AC and is terminated in a BNC connector.
Reference: MA002
Brand: MicroTec
The multimeter probes offer a quick and easy solution, where a permanent connection is not required. A test lead can be connected straight into the 4mm socket in the handle of the probe.
Reference: PP400
Brand: Pico Technology
HT extension leads are the simple accessory that allow you to take accurate secondary ignition measurements on COP ignition systems.
Reference: TA388
Brand: Pico Technology
The 2000 A current clamp allows you to measure up to 2000 amps without cutting, or disconnecting or stripping wires. Simply clamp the jaws around the cable to be tested and plug the clamp into your PicoScope. NOTE: This product is fitted with a PicoBNC+ interface, allowing it to be recognised by the software for auto-configuration.The product requires a...
Reference: MT619
Brand: MicroTec
The CAN Test Box gives you easy access to the 16 pins of the diagnostic connector that is fitted to all modern vehicles. Depending on the configuration of the vehicle, this may allow you to check power, ground and CAN Bus signal quality. With the test adaptors supplied you can connect your PicoScope automotive scope, or any other suitable scope, to the...
Reference: TA009
Brand: MicroTec
60A AC/DC current clamp with 4mm banana plug and 80 cm long coiled cable.The TA009 current clamp can measure currents from 10 mA up to 60 A with a switch-selectable high and low range. A simple pushbutton is included for zero adjustment when measuring DC current. The TA009 current clamp meets IEC 61010-1 CAT II 300V and is equipped with LED indication for...
This is a brand-new lead and offers dynamic measurement of resistance which is a feature we are using within our guided tests. The TA432 can be used to test diodes, in addition to resistance measurements.
NOTE: This product is fitted with a PicoBNC+ interface, allowing it to be recognised by the software for auto-configuration.
The product requires a PicoScope featuring the PicoBNC+ such as the PicoScope 4225A or PicoScope 4425A, and will not work with older PicoScope models.