- New

Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp?
Fuse extension leads are a simple accessory that can save you valuable time.
Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and replace it with a fuse extension lead. Now insert the fuse into the extension lead. To measure the current drawn, just connect your Pico current clamp to the extension lead.
Customer service (+45) 97 84 11 99
Fast delivery 1-2 business days
Secure payment via SSL connection
Reference: TA018
Brand: MicroTec
60A AC/DC current clamp with BNC connector and 2.5 meter long cable.The TA018 current clamp can measure currents from 10 mA up to 60 A with a switch-selectable high and low range. A simple pushbutton is included for zero adjustment when measuring DC current. The TA018 current clamp meets IEC 61010-1 CAT II 300V and is equipped with LED indication for...
Reference: TA019
Brand: Pico Technology
600A AC/DC current clamp with BNC connector.The TA019 current clamp is ideal for use with a PicoScope oscilloscope to display starter current waveforms, charging currents and for performing quick compression tests.
Reference: TA167
Brand: Pico Technology
This current clamp is suitable for measuring currents of upto 2000 A DC or 1500 A AC and is terminated in a BNC connector.
Reference: TA000
Brand: Pico Technology
The TA000 test lead has been custom made for automotive use with the PicoScope. Its long length (3 meters / approx 10 ft) allows the oscilloscope to be placed on the work bench away from the car being tested / repaired. A wide range of probes, clips and gators can be plugged into the 4mm connectors at the end of the cable. The cable is fully screened to...
Reference: TA167
Brand: Pico Technology
This current clamp is suitable for measuring currents of upto 2000 A DC or 1500 A AC and is terminated in a BNC connector.
Reference: TA010
Brand: Pico Technology
The TA010 has been designed to allow fuel injector and primary ignition waveforms to be measured using PicoScope oscilloscope products. The TA010 is a passive 20:1 attenuator. This means that a 20V signal at its input will appear as a 1V signal on the output. As the signal is attenuated, the TA010 allows voltages of up to 300 V to be measured. Please note...
Reference: TA018
Brand: MicroTec
60A AC/DC current clamp with BNC connector and 2.5 meter long cable.The TA018 current clamp can measure currents from 10 mA up to 60 A with a switch-selectable high and low range. A simple pushbutton is included for zero adjustment when measuring DC current. The TA018 current clamp meets IEC 61010-1 CAT II 300V and is equipped with LED indication for...
Reference: MI078
Brand: Pico Technology
The MI078 BNC to 4 mm adaptor connects two 4 mm “banana” plugs to a BNC socket.
Reference: BM319S
Brand: Brymen Technology
Brymen BM319s Automotive Multimeter incl. K-type temperature sensor and inductive pickup clip.The instrument is double insulated, equipped with high-efficiency fuses with control function and complies with IEC 1010-1 CAT II 1000V.
Reference: TA397
Brand: Pico Technology
Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection. Attempting to make a direct connection will almost certainly damage the measuring instrument. The TA397 is a capacitive pickup that simply connects around the insulation of an ignition circuit component such as a plug wire. This...
Reference: MA100
Brand: MicroTec
Test leads with 4mm safety banana plug at both ends, set of 5 colors (Red, black, yellow, green and blue).Can be used with all our probes, tips, clips and gators. Length: 1 meterMax. current: 15A
Reference: TA007
Brand: Pico Technology
The TA007 Insulation Piercing Test Clip set is ideally suited for automotive test and diagnosis.The contacts features insulated wires without cutting or stripping insulation. The spring loaded double V-clamp holds wire centered for piercing needle. This clip featured with pierces insulation on wires from 22 to 14AWG. Tiny hole left in insulation can...
Reference: TA473
Brand: Pico Technology
The TA473 current clamp is ideal for use with PicoScope automotive oscilloscopes for measuring currents between 10 mA and 60 A. This enables the PicoScope to display current waveforms for fuel injectors and fuel pumps. NOTE: This product is fitted with a PicoBNC+ interface, allowing it to be recognised by the software for auto-configuration.The product...
Reference: MA008
Brand: MicroTec
The Back Probe MT008 is very useful in back probing connectors to measure in an existing circuit without having to use a break out box or damage the wire isolation. The long, thin and flexible pins can easily be slided between the connector housing and the contacts in the connector.
Reference: TA035
Brand: Pico Technology
Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and replace it with a...
Reference: MA012
Brand: MicroTec
The MA012 AMP breakout lead enables you to take voltage readings from the numerous 2-pin sensors and actuators in the engine compartment. Simply connect the breakout lead into the existing cable loom, and then take the output signal from the two 4 mm banana plugs into the automotive oscilloscope using the TA000 test leads. The breakout cable gives access...
Reference: MA006
Brand: MicroTec
The 4mm socket in the back of the Dolphin clip offers an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 30mm opening diameter limit.
Reference: MI074
Brand: Pico Technology
Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection. Attempting to make a direct connection will almost certainly damage the measuring instrument. The MI074 is a capacitive pickup that simply connects around the insulation of an ignition circuit component such as a plug wire. This...
Reference: TA009
Brand: MicroTec
60A AC/DC current clamp with 4mm banana plug and 80 cm long coiled cable.The TA009 current clamp can measure currents from 10 mA up to 60 A with a switch-selectable high and low range. A simple pushbutton is included for zero adjustment when measuring DC current. The TA009 current clamp meets IEC 61010-1 CAT II 300V and is equipped with LED indication for...
Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp?
Fuse extension leads are a simple accessory that can save you valuable time.
Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and replace it with a fuse extension lead. Now insert the fuse into the extension lead. To measure the current drawn, just connect your Pico current clamp to the extension lead.