Secure payment
Brymen BM319s Automotive Multimeter incl. K-type temperature sensor and inductive pickup clip.
The instrument is double insulated, equipped with high-efficiency fuses with control function and complies with IEC 1010-1 CAT II 1000V.
Customer service (+45) 97 84 11 99
Fast delivery 1-2 business days
Secure payment via SSL connection
BM319s Professional choice of size and functions for automotive industry. Offers improved measurement functions, trouble-shooting features and accuracy to solve more problems on conventional and hybrid vehicles.
The Brymen BM319s multimeter has been specially designed for the automotive sector and is therefore packed with special features to do measurements on cars. For example, the RPM can be measured via test leads (IG-RPM) or via a special inductive pickup clip (IP-RPM), a Dwell angle and Duty Cycle of up to 12 cylinders can be measured and measurements can be made on multiple engines via the ms-FUEL injection detector.
In addition to the special automotive features, this multimeter also has most basic functionalities such as measuring DC & AC voltage and current, resistance, capacity, continuity, temperature and line-level frequency. A nice feature of this multimeter is that it has an excellent AutoRanging function, which can be overridden by manual ranging. There are also 4 trigger levels available to adjust the sensitivity of the meter to the type of signal of the motor. The polarity of these trigger levels can also be adjusted. Furthermore, the meter can also be used in poorly lit conditions thanks to the backlighted LCD display. All in all, the BM319s is an excellent automotive multimeter with a wide range of functions.
Unique automotive features:
Standard Accessories included:
Reference: 102135
Brand: Brymen Technology
Carrying punch (Softcase) for Brymen BM23X, BM25X, BM319s multimeters.
Reference: BM-S/FUSE-11A
Brand: Brymen Technology
Fuse for Brymen multimeter, 11A, 10x38mm, 20kA / 1000V
Reference: MA008
Brand: MicroTec
The Back Probe MT008 is very useful in back probing connectors to measure in an existing circuit without having to use a break out box or damage the wire isolation. The long, thin and flexible pins can easily be slided between the connector housing and the contacts in the connector.
Reference: TA004
Brand: Pico Technology
The crocodile (gator) clips are fully insulated with a 4mm socket in the handle, offering an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 11mm jaw opening limit.
Reference: TA162
Brand: Pico Technology
These probes are designed for back-probing under the insulation of multi-plug terminals. The TA161 and TA162 have flexible bends to improve access to difficult areas. Each probe fits onto the 4mm plug of our BNC to 4mm test leads.
Reference: MA002
Brand: MicroTec
The multimeter probes offer a quick and easy solution, where a permanent connection is not required. A test lead can be connected straight into the 4mm socket in the handle of the probe.
Reference: MA006
Brand: MicroTec
The 4mm socket in the back of the Dolphin clip offers an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 30mm opening diameter limit.
Reference: TA007
Brand: Pico Technology
The TA007 Insulation Piercing Test Clip set is ideally suited for automotive test and diagnosis.The contacts features insulated wires without cutting or stripping insulation. The spring loaded double V-clamp holds wire centered for piercing needle. This clip featured with pierces insulation on wires from 22 to 14AWG. Tiny hole left in insulation can...
Reference: TA009
Brand: MicroTec
60A AC/DC current clamp with 4mm banana plug and 80 cm long coiled cable.The TA009 current clamp can measure currents from 10 mA up to 60 A with a switch-selectable high and low range. A simple pushbutton is included for zero adjustment when measuring DC current. The TA009 current clamp meets IEC 61010-1 CAT II 300V and is equipped with LED indication for...
Reference: MI074
Brand: Pico Technology
Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection. Attempting to make a direct connection will almost certainly damage the measuring instrument. The MI074 is a capacitive pickup that simply connects around the insulation of an ignition circuit component such as a plug wire. This...
Reference: MA002
Brand: MicroTec
The multimeter probes offer a quick and easy solution, where a permanent connection is not required. A test lead can be connected straight into the 4mm socket in the handle of the probe.
Reference: MI078
Brand: Pico Technology
The MI078 BNC to 4 mm adaptor connects two 4 mm “banana” plugs to a BNC socket.
Reference: MT136
Brand: MicroTec
Softcase protective case for PicoScope-2000 series
Reference: MT619
Brand: MicroTec
The CAN Test Box gives you easy access to the 16 pins of the diagnostic connector that is fitted to all modern vehicles. Depending on the configuration of the vehicle, this may allow you to check power, ground and CAN Bus signal quality. With the test adaptors supplied you can connect your PicoScope automotive scope, or any other suitable scope, to the...
Reference: TA007
Brand: Pico Technology
The TA007 Insulation Piercing Test Clip set is ideally suited for automotive test and diagnosis.The contacts features insulated wires without cutting or stripping insulation. The spring loaded double V-clamp holds wire centered for piercing needle. This clip featured with pierces insulation on wires from 22 to 14AWG. Tiny hole left in insulation can...
Reference: TA018
Brand: MicroTec
60A AC/DC current clamp with BNC connector and 2.5 meter long cable.The TA018 current clamp can measure currents from 10 mA up to 60 A with a switch-selectable high and low range. A simple pushbutton is included for zero adjustment when measuring DC current. The TA018 current clamp meets IEC 61010-1 CAT II 300V and is equipped with LED indication for...
Reference: TA010
Brand: Pico Technology
The TA010 has been designed to allow fuel injector and primary ignition waveforms to be measured using PicoScope oscilloscope products. The TA010 is a passive 20:1 attenuator. This means that a 20V signal at its input will appear as a 1V signal on the output. As the signal is attenuated, the TA010 allows voltages of up to 300 V to be measured. Please note...
Reference: TA004
Brand: Pico Technology
The crocodile (gator) clips are fully insulated with a 4mm socket in the handle, offering an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 11mm jaw opening limit.
Reference: MA012
Brand: MicroTec
The MA012 AMP breakout lead enables you to take voltage readings from the numerous 2-pin sensors and actuators in the engine compartment. Simply connect the breakout lead into the existing cable loom, and then take the output signal from the two 4 mm banana plugs into the automotive oscilloscope using the TA000 test leads. The breakout cable gives access...
Reference: TA000
Brand: Pico Technology
The TA000 test lead has been custom made for automotive use with the PicoScope. Its long length (3 meters / approx 10 ft) allows the oscilloscope to be placed on the work bench away from the car being tested / repaired. A wide range of probes, clips and gators can be plugged into the 4mm connectors at the end of the cable. The cable is fully screened to...
Reference: MA006
Brand: MicroTec
The 4mm socket in the back of the Dolphin clip offers an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 30mm opening diameter limit.
Reference: TA019
Brand: Pico Technology
600A AC/DC current clamp with BNC connector.The TA019 current clamp is ideal for use with a PicoScope oscilloscope to display starter current waveforms, charging currents and for performing quick compression tests.
Reference: MA008
Brand: MicroTec
The Back Probe MT008 is very useful in back probing connectors to measure in an existing circuit without having to use a break out box or damage the wire isolation. The long, thin and flexible pins can easily be slided between the connector housing and the contacts in the connector.
Reference: TA162
Brand: Pico Technology
These probes are designed for back-probing under the insulation of multi-plug terminals. The TA161 and TA162 have flexible bends to improve access to difficult areas. Each probe fits onto the 4mm plug of our BNC to 4mm test leads.
Brymen BM319s Automotive Multimeter incl. K-type temperature sensor and inductive pickup clip.
The instrument is double insulated, equipped with high-efficiency fuses with control function and complies with IEC 1010-1 CAT II 1000V.
