Secure payment
The MI029 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black 4mm safety banana plugs.
Customer service (+45) 97 84 11 99
Fast delivery 1-2 business days
Secure payment via SSL connection
Reference: TA004
Brand: Pico Technology
The crocodile (gator) clips are fully insulated with a 4mm socket in the handle, offering an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 11mm jaw opening limit.
Reference: TA162
Brand: Pico Technology
These probes are designed for back-probing under the insulation of multi-plug terminals. The TA161 and TA162 have flexible bends to improve access to difficult areas. Each probe fits onto the 4mm plug of our BNC to 4mm test leads.
Reference: MA002
Brand: MicroTec
The multimeter probes offer a quick and easy solution, where a permanent connection is not required. A test lead can be connected straight into the 4mm socket in the handle of the probe.
Reference: MA006
Brand: MicroTec
The 4mm socket in the back of the Dolphin clip offers an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 30mm opening diameter limit.
Reference: MA012
Brand: MicroTec
The MA012 AMP breakout lead enables you to take voltage readings from the numerous 2-pin sensors and actuators in the engine compartment. Simply connect the breakout lead into the existing cable loom, and then take the output signal from the two 4 mm banana plugs into the automotive oscilloscope using the TA000 test leads. The breakout cable gives access...
Reference: TA050
Brand: Pico Technology
Attenuator set: 3-6-10-20 dB, 1 GHz 50 Ω 1 W BNC (m-f). The TA050 attenuator set consists of four coaxial attenuators designed for use with signals up to 1 GHz. Each attenuator has a male and a female BNC connector.
Reference: MI029-1
Brand: Pico Technology
The MI029-1 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black 4 mm "banana" plugs.
Reference: MA100
Brand: MicroTec
Test leads with 4mm safety banana plug at both ends, set of 5 colors (Red, black, yellow, green and blue).Can be used with all our probes, tips, clips and gators. Length: 1 meterMax. current: 15A
Reference: TA035
Brand: Pico Technology
Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and replace it with a...
Reference: MI030
Brand: Pico Technology
The MI030 is a 1.8m BNC plug to BNC plug cable, useful for connecting signal sources with BNC output to oscilloscope inputs.
Reference: TA139
Brand: Pico Technology
Ta139 are replacement logic test clips for the 20-way digital input cable, used on the digital ports of Mixed Signal Oscilloscopes (MSOs) in the PicoScope 2000, 3000 and 5000 series. One package contains 10 test clips, 8 reds and 2 blacks.
Reference: MT619
Brand: MicroTec
The CAN Test Box gives you easy access to the 16 pins of the diagnostic connector that is fitted to all modern vehicles. Depending on the configuration of the vehicle, this may allow you to check power, ground and CAN Bus signal quality. With the test adaptors supplied you can connect your PicoScope automotive scope, or any other suitable scope, to the...
Reference: TA034
Brand: Pico Technology
Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and replace it with a...
Reference: MI031
Brand: Pico Technology
The MI029 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black crocodile clips.
Reference: TA206
Brand: Pico Technology
The TA206 maxi fuse extension lead is designed to be used with standard maxi automotive fuses. The maxi fuse is a large blade-style fuse used to protect high-current circuits and handle large inrush currents on some vehicles.
Reference: TA168
Brand: Pico Technology
The TA168 JCASE fuse extension lead gives easier access to standard and low profile JCASE fuses. JCASE is a cartridge style fuse with female terminal design, providing both increased time delay and low voltage drop to protect high current circuits & handle inrush currents.
Reference: PP967
Brand: Pico Technology
Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and replace it with a...
Reference: MI078
Brand: Pico Technology
The MI078 BNC to 4 mm adaptor connects two 4 mm “banana” plugs to a BNC socket.
Reference: TA136
Brand: Pico Technology
The TA136 is a replacement 20-way digital input cable that interfaces up to 16 digital signals to the digital ports on PicoScope 2000, 3000 and 5000 Series Mixed Signal Oscilloscopes (MSOs). Digital inputs: 16 Ground connections: 4 Length: 25 cm (approx. 9.8 in)
Reference: TA051
Brand: Pico Technology
Feed-through attenuator, 1 GHz 50 Ω 1 W BNC (m-f). The TA051 feed-through attenuator is a coaxial terminator with BNC connectors. It is useful for connecting signals from 50 Ω sources into instruments with 1 MΩ impedance inputs, such as oscilloscopes.
The MI029 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black 4mm safety banana plugs.
