Secure payment
There are 86 products.
Reference: TA162
Brand: Pico Technology
These probes are designed for back-probing under the insulation of multi-plug terminals. The TA161 and TA162 have flexible bends to improve access to difficult areas. Each probe fits onto the 4mm plug of our BNC to 4mm test leads.
Reference: PP917
Brand: Pico Technology
Low Cost USB oscilloscope.Bandwidth 10 MHz, sample rate 100 MS/s, record length 8 K With the PicoScope 2204A ultra-compact USB oscilloscope you get an oscilloscope, spectrum analyzer and arbitrary waveform generator all in one powerful and affordable device. 2 x 60MHz oscilloskopprober (x1/X10) are optional.
Reference: TA000
Brand: Pico Technology
The TA000 test lead has been custom made for automotive use with the PicoScope. Its long length (3 meters / approx 10 ft) allows the oscilloscope to be placed on the work bench away from the car being tested / repaired. A wide range of probes, clips and gators can be plugged into the 4mm connectors at the end of the cable. The cable is fully screened to...
Reference: EL-USB-2
Brand: Lascar Electronics
Lascar Humidity, Temperature and Dewpoint Logger with USB Interface. Humidity, temperature and dew point logger plugs straight into a PC's USB port.Software is included with each logger
Reference: MT920
Brand: MicroTec
The 2–Channel Starter Kit gives you the lowest possible cost entry into PicoScope ownership.The kit comes complete with a basic set of leads and clips to allow you to perform many common tasks including testing most sensors.Over time accessories such as current clamps and ignition probes can be added to expand its uses. Note: Comes with the standard...
Reference: BAT-3V6-1/2AA
Brand: Lascar Electronics
Non-rechargeable 1/2 AA lithium battery for use with most Lascar data loggers (excluding EL-USB-1-PRO, EL-USB-1-RCG, EL-USB-LITE & EL-USB-RT).
Reference: TA018
Brand: MicroTec
60A AC/DC current clamp with BNC connector and 2.5 meter long cable.The TA018 current clamp can measure currents from 10 mA up to 60 A with a switch-selectable high and low range. A simple pushbutton is included for zero adjustment when measuring DC current. The TA018 current clamp meets IEC 61010-1 CAT II 300V and is equipped with LED indication for...
Reference: TA004
Brand: Pico Technology
The crocodile (gator) clips are fully insulated with a 4mm socket in the handle, offering an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 11mm jaw opening limit.
Reference: EL-USB-1
Brand: Lascar Electronics
Lascar Temperature Logger with USB Interface.USB Temperature Data Logger, IP67 rated, supplied with configuration software.
Reference: MI007
Brand: Pico Technology
This high quality, general purpose oscilloscope probe has a 60 MHz bandwidth. A two position slide switch allows attenuation of either x1 or x10 to be selected.
Reference: EL-USB-CASE
Brand: Lascar Electronics
Protective metal case for EL-USB-1 and EL-USB-2 Suitable for use with EL-USB-1 and EL-USB-2 Rugged metal alloy design Waterproof protection to IP-67/NEMA-4X
Reference: PP966
Brand: Pico Technology
Low Cost USB oscilloscope.Bandwidth 25 MHz, sample rate 200 MS/s, record length 16 K With the PicoScope 2205A ultra-compact USB oscilloscope you get an oscilloscope, spectrum analyzer and arbitrary waveform generator all in one powerful and affordable device. 2 x 100 MHz oscilloscope probes (x1/x10) are optional.
Reference: EL-USB-1-LCD
Brand: Lascar Electronics
Lascar Temperature Logger with LCD display and USB Interface.USB Temperature Data Logger, supplied with configuration software.
Reference: MA006
Brand: MicroTec
The 4mm socket in the back of the Dolphin clip offers an easy connection to a test lead. The toothed grip offers good contact on fine wire, with a 30mm opening diameter limit.
Reference: EL-USB-3
Brand: Lascar Electronics
Lascar Voltage Data Logger with USB Interface. Voltage logger plugs straight into a PC's USB port.Software is included with each logger.
Reference: MA008
Brand: MicroTec
The Back Probe MT008 is very useful in back probing connectors to measure in an existing circuit without having to use a break out box or damage the wire isolation. The long, thin and flexible pins can easily be slided between the connector housing and the contacts in the connector.
Reference: TA010
Brand: Pico Technology
The TA010 has been designed to allow fuel injector and primary ignition waveforms to be measured using PicoScope oscilloscope products. The TA010 is a passive 20:1 attenuator. This means that a 20V signal at its input will appear as a 1V signal on the output. As the signal is attenuated, the TA010 allows voltages of up to 300 V to be measured. Please note...
Reference: MI074
Brand: Pico Technology
Due to the high voltages involved in secondary ignition systems, it is not possible to make measurements by direct connection. Attempting to make a direct connection will almost certainly damage the measuring instrument. The MI074 is a capacitive pickup that simply connects around the insulation of an ignition circuit component such as a plug wire. This...
Reference: SE001
Brand: Pico Technology
The SE001 is an exposed junction thermocouple with fiberglass insulated, 0.3 mm twisted pair conductor.Choose a length of 1, 2 or 5 meters. All Pico thermocouples are manufactured to strict industry tolderances stated in IEC 60584-2 :1993 / BS EN 60584-1:2013.
Reference: MI031
Brand: Pico Technology
The MI029 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black crocodile clips.
Reference: EL-SIE-2+
Brand: Lascar Electronics
Lascar EL-SIE-2+ High Accuracy temperature and humidity data logger with LCD display and USB Interface.EasyLog Cloud compliant.
Reference: MI078
Brand: Pico Technology
The MI078 BNC to 4 mm adaptor connects two 4 mm “banana” plugs to a BNC socket.
Reference: TA009
Brand: MicroTec
60A AC/DC current clamp with 4mm banana plug and 80 cm long coiled cable.The TA009 current clamp can measure currents from 10 mA up to 60 A with a switch-selectable high and low range. A simple pushbutton is included for zero adjustment when measuring DC current. The TA009 current clamp meets IEC 61010-1 CAT II 300V and is equipped with LED indication for...
Reference: BAT 3V6 2/3AA H TEMP
Brand: Lascar Electronics
A specialist battery that allows for operation of the EL-USB-1-PRO logger at high temperature.
