
Reference: MI029
Brand: Pico Technology
BNC plug to 4mm safety banana plugs (1.2m)
The MI029 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black 4mm safety banana plugs.
Attenuator set: 3-6-10-20 dB, 1 GHz 50 Ω 1 W BNC (m-f).
The TA050 attenuator set consists of four coaxial attenuators designed for use with signals up to 1 GHz. Each attenuator has a male and a female BNC connector.
Customer service (+45) 97 84 11 99
Fast delivery 1-2 business days
Secure payment via SSL connection
Usage note
The TA050 attenuators must be used with a matched 50 Ω source and load. If you wish to attenuate a signal before feeding it into a high-impedance measuring instrument, you must add a 50 Ω feedthrough terminator such as the Pico Technology TA051 feedthrough terminator.
Figure 1: Using with a 50 Ω load
Figure 2: Using with a high-impedance load such as an oscilloscope, spectrum analyser or frequency counter
Reference: MI029
Brand: Pico Technology
The MI029 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black 4mm safety banana plugs.
Reference: MI031
Brand: Pico Technology
The MI029 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black crocodile clips.
Reference: MI030
Brand: Pico Technology
The MI030 is a 1.8m BNC plug to BNC plug cable, useful for connecting signal sources with BNC output to oscilloscope inputs.
Reference: TA051
Brand: Pico Technology
Feed-through attenuator, 1 GHz 50 Ω 1 W BNC (m-f). The TA051 feed-through attenuator is a coaxial terminator with BNC connectors. It is useful for connecting signals from 50 Ω sources into instruments with 1 MΩ impedance inputs, such as oscilloscopes.
Reference: MT619
Brand: MicroTec
The CAN Test Box gives you easy access to the 16 pins of the diagnostic connector that is fitted to all modern vehicles. Depending on the configuration of the vehicle, this may allow you to check power, ground and CAN Bus signal quality. With the test adaptors supplied you can connect your PicoScope automotive scope, or any other suitable scope, to the...
Reference: TA136
Brand: Pico Technology
The TA136 is a replacement 20-way digital input cable that interfaces up to 16 digital signals to the digital ports on PicoScope 2000, 3000 and 5000 Series Mixed Signal Oscilloscopes (MSOs). Digital inputs: 16 Ground connections: 4 Length: 25 cm (approx. 9.8 in)
Reference: TA206
Brand: Pico Technology
The TA206 maxi fuse extension lead is designed to be used with standard maxi automotive fuses. The maxi fuse is a large blade-style fuse used to protect high-current circuits and handle large inrush currents on some vehicles.
Reference: TA168
Brand: Pico Technology
The TA168 JCASE fuse extension lead gives easier access to standard and low profile JCASE fuses. JCASE is a cartridge style fuse with female terminal design, providing both increased time delay and low voltage drop to protect high current circuits & handle inrush currents.
Reference: MI078
Brand: Pico Technology
The MI078 BNC to 4 mm adaptor connects two 4 mm “banana” plugs to a BNC socket.
Reference: MA012
Brand: MicroTec
The MA012 AMP breakout lead enables you to take voltage readings from the numerous 2-pin sensors and actuators in the engine compartment. Simply connect the breakout lead into the existing cable loom, and then take the output signal from the two 4 mm banana plugs into the automotive oscilloscope using the TA000 test leads. The breakout cable gives access...
Reference: MI029
Brand: Pico Technology
The MI029 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black 4mm safety banana plugs.
Reference: TA051
Brand: Pico Technology
Feed-through attenuator, 1 GHz 50 Ω 1 W BNC (m-f). The TA051 feed-through attenuator is a coaxial terminator with BNC connectors. It is useful for connecting signals from 50 Ω sources into instruments with 1 MΩ impedance inputs, such as oscilloscopes.
Reference: MA100
Brand: MicroTec
Test leads with 4mm safety banana plug at both ends, set of 5 colors (Red, black, yellow, green and blue).Can be used with all our probes, tips, clips and gators. Length: 1 meterMax. current: 15A
Reference: TA000
Brand: Pico Technology
The TA000 test lead has been custom made for automotive use with the PicoScope. Its long length (3 meters / approx 10 ft) allows the oscilloscope to be placed on the work bench away from the car being tested / repaired. A wide range of probes, clips and gators can be plugged into the 4mm connectors at the end of the cable. The cable is fully screened to...
Reference: TA034
Brand: Pico Technology
Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and replace it with a...
Reference: TA285
Brand: Pico Technology
USB Type-C is a new cable and connector standard that allows smaller USB devices and faster data transfers. It also simplifies the connection process with just the one type of reversible connector on both ends of a reversible cable.
Reference: MI029-1
Brand: Pico Technology
The MI029-1 is a 1.2 m (3.9 ft) cable for connecting a BNC socket to two red and black 4 mm "banana" plugs.
Reference: TA139
Brand: Pico Technology
Ta139 are replacement logic test clips for the 20-way digital input cable, used on the digital ports of Mixed Signal Oscilloscopes (MSOs) in the PicoScope 2000, 3000 and 5000 series. One package contains 10 test clips, 8 reds and 2 blacks.
Reference: PP967
Brand: Pico Technology
Do you need to measure the current through a circuit but can’t find anywhere on the vehicle where you can connect your current clamp? Fuse extension leads are a simple accessory that can save you valuable time. Fuse extension leads are quick and easy to use: simply remove the fuse (of the circuit you wish to test) from your fusebox and replace it with a...
Reference: MI030
Brand: Pico Technology
The MI030 is a 1.8m BNC plug to BNC plug cable, useful for connecting signal sources with BNC output to oscilloscope inputs.
Attenuator set: 3-6-10-20 dB, 1 GHz 50 Ω 1 W BNC (m-f).
The TA050 attenuator set consists of four coaxial attenuators designed for use with signals up to 1 GHz. Each attenuator has a male and a female BNC connector.